Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You might discover that your garage door opener has actually been giving you problems, so you need to repair it. You can repair it by changing a motherboard, a photo-eye sensor, the major drive equipment, or the set-limit buttons. You can additionally examine if the safety and security sensing units are functioning appropriately.

Replacing a circuit board

Changing a circuit board for your garage door opener needs a few steps and devices. First, you need to turn off the breaker and also detach any cables. Next off, open the circuit board cover. This will certainly assist you to detect the problem as well as figure out if you require a new board. Next off, get rid of the old board and also its wire adapters.

You can after that proceed to change the motherboard. The replacement process is easy and also takes around 10 minutes. A new circuit board will certainly set you back concerning $80. To protect your brand-new circuit board from power surges, you can acquire a rise guard.

Changing a photo-eye sensor

Replacing a photo-eye sensing unit can be a relatively basic task. First, remove the sensor from the door as well as make certain it is located appropriately. If the sensing unit is angled by any means, it may not be getting the right signal, which can be creating the strobe lights. If you observe that the photo-eyes run out positioning, you might require to have a technician come and deal with the trouble.

The photo-eye sensing unit consists of 2 items that place outside of the door tracks and towards the floor. The picture eyes will have a small LED light as well as need to be solid in color. If the light is blinking, its likely the photo-eye is faulty as well as will certainly need to be replaced.

Replacing a main drive gear

To replace a garage door opener major drive gear, start by getting rid of the cap from the chain wheel. Next off, eliminate both screws holding the drive equipment to the gear setting up. Now, you can loosen the 3 tension pins. Press them from both sides and after that remove them. Then, separate the 3 wires from the garage door opener electric motor. These cords ought to be white, red, and also blue.

Once you have removed the old gear, mount a brand-new one. Make sure to grease it well. Place the brand-new gear right into the shaft, ensuring to align the installing holes. See to it the equipment and sprocket assembly are located appropriately to ensure smooth procedure. Next, utilize a hammer and a nail to drive a pin into the brand-new gear.

Readjusting the set-limit switches

The very first thing you should do if your garage door is not functioning properly is to check the set-limit switches. You might need to adjust them to make sure that the door closes earlier or stops prior to it gets to the floor. You can examine this by considering your garage doors handbook or online.

To readjust the set-limit buttons, youll require a screwdriver or socket. Adjust the handle clockwise or counterclockwise till the door goes up and also quits, or lowers its range. To check for proper travel range, measure the void from the bottom of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Main St Ste 105, Keller, TX 76248, United States

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Leave a Reply

Your email address will not be published. Required fields are marked *

Back To Top